Q. I'm getting ready to buy backer board for a ceramic tile project. There are different types out there, and I'm a little confused. Which backer boards would you use and which would you avoid? You've mentioned using cement backer board; do you still feel that's the best product? Also, please share any backer board installation tips.

A. To be more precise, I've installed lots of concrete backer board for years, all with good results. The concrete is unaffected by any water that manages to get behind the ceramic tile. But these concrete products are heavy, problematic to cut and can wick water, causing wood rot. Recently I've been experimenting with some of the alternative backer boards. The most recent one I've worked with has a water-resistant gypsum core with a fiberglass mat backing and a handsome blue waterproof coating on the side that the tile adheres to. This material is code-approved and recommended by a leading ceramic tile association. I find this material far easier to work with than the cement backer boards. I don't miss the small pieces of sand and grit that scratch tub finishes!

Using this particular product also saves a step in the building process. If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it's attached to. Since the concrete can absorb and wick moisture, the barrier prevents wood rot if the backer board gets saturated with water.

I witnessed first hand what happens when cement backer board is installed without a moisture barrier. Last month I demolished a 25-year-old bathroom that had waterlogged cement board in the shower. Because no water barrier was installed, the bottoms of some of the wall studs were beginning to show water damage.

When I first got into the construction business nearly 35 years ago, a moisture-resistant drywall was the backer board of choice. It had a green paper so you could distinguish it easily from traditional drywall. Millions of square feet of this was installed in bathrooms, some by me, until we in the building trades discovered it didn't do too well. Water passed through grout joints and eventually caused the green paper to fall apart. Virtually every building code now shuns this product for use in wet areas. I would never install this product behind tiles that were subject to water splashing on them.

As you prepare to install your ceramic backer board, the first thing to do is stop and read all the written instructions that deal with installing backer board. The product that I used with the bright blue coating had the instructions attached to each sheet. This is very helpful, and it can save you time and money by not having a failure at some point down the road.

Don't underestimate the importance of using the correct fasteners when installing the backer board on walls. The combined weight of the board and the tiles you'll attach to it is considerable. Absolutely use screws instead of nails -- and not just drywall screws.

You can usually find special backer board screws that have oversized, bugle-shaped heads that securely fasten the board to wood or metal studs. Be sure the screws are coated so they don't rust. It's also important to drive the screws flush with the surface of the board. Don't allow them to tear the coated facing of the board.

If you're installing your backer board in a shower or tub, don't allow the board to come into contact with the concrete shower pan or the tub ledge. I prefer to hold up the backer board one-quarter inch off tub ledges and one-half inch off a concrete substrate in a poured shower. Holding the board up prevents the edge from sitting in any water.

Cutting backer board, especially if it's a gypsum-core backer board, is done with a simple razor knife. You score the surface with the razor and then snap the board, creating a clean line. Then use the razor to cut the fiberglass backing. It's the same procedure used to cut regular drywall.

Take your time to make sure that wall studs are plumb and in the same plane before you install backer board. These products conform exactly to what you fasten them to. If you want your tile to go in easily, the backer board itself must be plumb and flat.

Make sure the backer board you use on floors is attached to a sound subfloor. Screw down the wood subfloor to the floor joists before installing the backer board. If the floor seems springy or bouncy, you'll likely end up with cracked tile. Be sure to install the backer board in a bed of cement thinset mortar to ensure there are no hollow spots or voids in between the backer board and the wood subfloor.

All of Tim's past columns and videos are available at AsktheBuilder.com. Discover answers to thousands of questions. Subscribe to get free alerts each time a new video or column is uploaded to AsktheBuilder.com.

Note to readers: if you purchase something through one of our affiliate links we may earn a commission.

Registration on or use of this site constitutes acceptance of our User Agreement, Privacy Policy and Cookie Statement, and Your California Privacy Rights (User Agreement updated 1/1/21. Privacy Policy and Cookie Statement updated 7/1/2022).

© 2022 Advance Local Media LLC. All rights reserved (About Us). The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Advance Local.

Community Rules apply to all content you upload or otherwise submit to this site.